Woodline's Band Saw Table Inserts
Woodline's Band Saw Table Inserts

Band Saw Table Inserts

4.62 (24)

Band saw inserts will inevitably get messed up over time. The answer? Woodline makes replacements for most popular models. Get an inexpensive set of replacement inserts and get back to work. 3 inserts per package. Rectangular inserts come in 2 packs.

*Semi-rigid plastic
*Will not hurt blade's teeth 

 

$10.95 - $19.95
/

Select an option to add this to your cart.

Woodline's Band Saw Table Inserts
Band Saw Table Inserts
$10.95 - $19.95
TI1 Delta 14" & Imports, Shopsmith, 12" Sears (91"blade), 18" Delta, 2-1/2" Outside Diameter, Lip thickness ≈ 0.099" & 2-3/16" Inside Diameter TI1
$11.95 /each
TI2 Delta 10", 16" Grizzly (113"blade), 15" General, Powermatic 141, 2-1/4" Outside Diameter, Lip thickness ≈ 0.081" & 1-7/8" Inside Diameter TI2
$11.95 /each
TI3 Jet 12", 14" & 18" , 2-1/2" Outside Diameter, Lip thickness ≈ 0.110" & 1-3/4" Inside Diameter with Notch - NOTE: Does NOT fit 116" blade version TI3
$11.95 /each
TI4 Sears 12" (Model #113.24350 or 113.243300) 3-3/8" Outside Diameter & thickness ≈ 0.090" TI4
$10.95 /each
TI5 Powermatic 14", 12" Sears (89-1/2"blade), 14" Rikon (111"blade-must remove pin), 14" Mini Max, 2-11/16" w/Slot & Pin & Thickness ≈ 0.158" TI5
$13.95 /each
TI6 Jet 14" (116" Blade), 2.72" Outside, Lip thickness ≈ 0.11" & 2.4" Inside with Notch TI6
$13.95 /each
TI7 Grizzly 17" (G0555X, G0457, G0513, G0514, G0640X), 2.725" Outside, Lip thickness ≈ 0.15" & 2-1/4" Inside TI7
$13.95 /each
TI8 Laguna 1412, 14BX & 18BX 5.269" Long, 2.910" Wide, Thickness ≈ 0.195" Pack of 2. One is zero clearance and one is standard TI8
$19.95 /each
TI9 Rikon 10-305 2-3/8" Dia, Lip thickness ≈ 0.120". Pack of 3, two zero clearance and one standard TI9
$13.95 /each
TI10 Jet JBS-18 3-3/16" Dia, Lip thickness ≈ 0.105" with notches . Pack of 3, two zero clearance and one standard TI10
$13.95 /each
TI11 Fits Powermatic PM2013B, 3" Outside Diameter, 2-1/4" Inside Diameter TI11
$13.95 /each
TI12 Fits Bauer 14", Outside Diameter, Inside Diameter TI12
$13.95 /each
Total:

Questions & Answers

Have a Question?

Ask a Question

  • I need insert for Rigid 14” band saw. Which one fits.

    With a few exceptions, TI1 is the insert for a Rigid 14" bandsaw. If you measure it should be a 2-1/2" diameter hole.

    https://www.woodline.com/products/band-saw-table-inserts?_pos=1&_sid=56378f1a7&_ss=r&variant=5678617537

  • Do you have bandsaw table inserts for Mini Max 24, MM24 03/505

    We don’t have one that we know of, but if you can provide the size, we can check our database.

  • Do you make table inserts for Rikon 14 inch bandsaw

    TI-5 fits the Rikon 14" with 111" blade.

  • Do you have an insert for a JBS 20 bandsaw? Looks like it is a 2-3/4 OD. I have tried 3 different online sources and all were too small.

    We have Ti-6 which is  2.72" OD x 2.4" ID x 0.11" lip thickness and 2.725" and Ti-7 2.725" OD x 2.25" ID x 0.15" lip thickness.

    If neither of these work we can make a custom for you. Cost is $19.99 for set of three. We will need OD x ID x lip thickness. Along with model number and blade length of saw. If you have an original you can send us that and we can take measurement for you.

  • in need an insert for a powermatic pm2013b, 3 inches

    Send the dimensions to [email protected] We will need overall diameter and thickness of the lip it sits on and we will see if we have one that size in our one-off file. Also give us name and model of the bandsaw.
    If we have to make it from stratch there's a $24.00 fee for set of 3.

  • I have a grizzly 16" bandsaw and a Ridgid 14" bandsaw and they both need inserts that are 2-7" outside diameter. The TI1 that you sent are just a little too large. Can I return them for the correct size? Thanks

    We do not make that size. It could go through custom shop. If you have an original we can use it to make you some. Cost for this service is $40 for set of 3.

  • i need a i.5 inch bandsaw table insert

    Send the dimensions to [email protected] We will need overall diameter and thickness of the lip it sits on and we will see if we have one that size in our one-off file. Also give us name and model of the bandsaw.
    If we have to make it from stratch there's a $24.00 fee for set of 3.

You may also like

Recently viewed